Every day introduces us to more and more motion sensors on the market. Numerous companies have chosen to produce cutting-edge products capable of meeting the needs of an increasingly large audience.
Simply knowing about the importance of a light sensor will propel you to get at least one and install the same. If you want to know the benefits of using a light sensor and how to properly fit them to your door, this article is for you. Without further ado, Let’s dive in.
Light Sensor and Its Benefits
A light sensor is a device that can sensitively sense the light energy of ultraviolet light to infrared light and transform the light energy into an electrical signal.
It is a kind of motion detector light and it has become increasingly popular over the years. It would interest you to know that motion sensor lights have played a very vital role in security as they serve as a stop towards criminal activities. Motion sensor lights serve as home security systems.
In addition to these benefits, installing a sensor security light saves both cost and energy. It is also used for lighting up the home as it ensures safety when walking.
Having seen all of these, you need to know what smart features you need to look out for when choosing motion sensor lights.
What You Must Consider When Choosing Motion Light Sensors
Bulb Type
You must consider the bulb type as there are various types of bulbs in the market, such as LED light, glowing, and fluorescent. Of all these types of bulbs, you should opt for LED light bulbs as they last longer than the other radiators.
Light Pattern
You need to consider the light pattern. While some lights illuminate a whole place, some are designed to illuminate a certain spot. The one which illuminates a large place is known as a floodlight while the one for a particular area is known as a spotlight. Floodlights and spotlights are common in LED outdoor lights.
How To Install Or Fit A Light Sensor To A Door
Installing motion sensors is not difficult. There are various models on the market equipped with different technologies. Those with wireless technology have an important advantage: they allow you to avoid having to make changes to the electrical system. This results in lower maintenance costs.
Fitting or installing a light sensor is largely dependent on the type of light accessories you purchase. Fitting a brand new light sensor to a door is quite different from replacing an existing one. You would need a screwdriver and an outdoor motion switch to do this.
Your light sensor kit will come with wiring nuts to help you in connecting your motion light sensor. Follow closely to find out how to fit your new sensor security light.
To install a motion sensor you need:
- The chosen model;
- Drill
- Locknut
Once you have all three elements available, you can proceed with the installation with this step by step guide:
Find a Model That is Compatible With the Lighting System
After making your choice, you can start the assembly activities. The latter depends on some elements such as the presence or absence of the knockout, which can be included in the motion sensor. If not, you need to drill it using the drill and a 3mm bit.
Turn Off the Switch
If the tester shows that there is no voltage, the protections must be removed and separated from each other. In addition, the ground wire must also be disconnected.
Identify the Surface on Which the Sensor Can be Installed.
Using the drill you can create the entrance hole and eliminate any sharp surfaces. After obtaining the hole, it is necessary to make sure that no metal filings remain and if there are, remove them.
Insert the Rubber Brush
The motor shaft will make the cables penetrate through the hole that has been created.
Use the Locking Nut to Fix the Sensor
As for the cables, it is advisable to orient yourself by taking into account the three colours: black, white and red. The white must be connected with that of the main wiring.
The second is to the red one and then to the main node. Connect the hot wire to the motion detector, the black and red wire to the light's hot wire, and tie the neutral wires together.
Wrap the Nuts Using Insulating Tape
Once the bundle has been fixed with the supplied cap, then wrap the nuts using your insulating tape.
Reconnect the Ground Wire
After putting the switch back to ON and darkness sets in, you can test the sensitivity of your new motion light sensor.
Having done all of this you will seal the light fixture, which could also be a DIY light fixture, with sealants.
Where Can I Get Motion Light Sensors?
LED Supplier offers the very best motion sensor lights suited to your needs. We have some featured products on our wall and you can access these products by simply visiting our website via your browser.
Some of our products include our under cabinet lighting, LED Downlights, LED Striplights, LED Batten Lights, Fire-rated Downlights, LED Panel Lights, Commercial Lighting, Work Light, Jody Wall Light amongst many others.
We help you light up the view of your kitchen, porch, office, garden, wall, bathroom and every other place of your choice as your satisfaction is our priority.
Conclusion
We designed our security light sensor this way for your convenience. If you have further questions on how to install your newly purchased motion light sensor, please contact us here and we would reply to you as soon as possible.
Your safety is our priority; secure your home now by getting any of our products. Feel free to give our products ratings when you have used them also.
